Graphene Electronics: Single-step Technique Produces Both P-type and N-type Doping for Future Devices

A simple one-step process that produces both n-type and p-type doping of large-area graphene surfaces could facilitate use of the promising material for future electronic devices.  The doping technique can also be used to increase conductivity in graphene nanoribbons used for interconnects.

Researchers Raghunath Murali and graduate student Kevin Brenner(front) perform electrical measurements on a graphene sample under high vacuum in a cryogenic probe station. (Click image for high-resolution version. Credit: Gary Meek)

By applying a commercially-available spin-on-glass (SOG) material to graphene and then exposing it to electron-beam radiation, researchers at the Georgia Institute of Technology created both types of doping by simply varying the exposure time.  Higher levels of e-beam energy produced p-type areas, while lower levels produced n-type areas.

The technique was used to fabricate high-resolution p-n junctions.  When properly passivated, the doping created by the SOG is expected to remain indefinitely in the graphene sheets studied by the researchers.

“This is an enabling step toward making possible complementary metal oxide graphene transistors,” said Raghunath Murali, a senior research engineer in Georgia Tech’s Nanotechnology Research Center.

A paper describing the technique appears this week in the journal Applied Physics Letters.  The research was supported by the Semiconductor Research Corporation and the Defense Advanced Research Projects Agency (DARPA) through the Interconnect Focus Center.

Graduate student Kevin Brenner holds a fabricated graphene sample. (Click image for high-resolution version. Credit: Gary Meek)

In the new doping process, Murali and graduate student Kevin Brenner begin by removing flakes of graphene one to four layers thick from a block of graphite.  They place the material onto a surface of oxidized silicon, then fabricate a four-point contact device.

Next, they spin on films of hydrogen silsesquoxane (HSQ), then cure certain portions of the resulting thin film using electron beam radiation.  The technique provides precise control over the amount of radiation and where it is applied to the graphene, with higher levels of energy corresponding to more cross-linking of the HSQ.

“We gave varying doses of electron-beam radiation and then studied how it influenced the properties of carriers in the graphene lattice,” Murali said.  “The e-beam gave us a fine range of control that could be valuable for fabricating nanoscale devices.  We can use an electron beam with a diameter of four or five nanometers that allows very precise doping patterns.”

Electronic measurements showed that a graphene p-n junction created by the new technique had large energy separations, indicating strong doping effects, he added.

Graduate student Kevin Brenner holds a fabricated graphene sample. (Click image for high-resolution version. Credit: Gary Meek)

Researchers elsewhere have demonstrated graphene doping using a variety of processes including soaking the material in various solutions and exposing it to a variety of gases.  The Georgia Tech process is believed to be the first to provide both electron and hole doping from a single dopant material.

Doping processes used for graphene are likely to be significantly different from those established for silicon use, Murali said.  In silicon, the doping step substitutes atoms of a different material for silicon atoms in the material’s lattice.

In the new single-step process for graphene, the doping is believed to introduce atoms of hydrogen and oxygen in the vicinity of the carbon lattice.  The oxygen and hydrogen don’t replace carbon atoms, but instead occupy locations atop the lattice structure.

“Energy applied to the SOG breaks chemical bonds and releases hydrogen and oxygen which bond with the carbon lattice,” Murali said.  “A high e-beam energy converts the whole SOG structure to more of a network, and then you have more oxygen than hydrogen, resulting in a p-type doping.”

Researchers Raghunath Murali and graduate student Kevin Brenner (front) display a fabricated graphene sample. (Click image for high-resolution version. Credit: Gary Meek)

In volume manufacturing, the electron beam radiation would likely be replaced by a conventional lithography process, Murali said.  Varying the reflectance or transmission of the mask set would control the amount of radiation reaching the SOG, and that would determine whether n-type or p-type areas are created.

“Making everything in a single step would avoid some of the expensive lithography steps,” he said.  “Gray-scale lithography would allow fine control of doping across the entire surface of the wafer.”

For doping bulk areas such as interconnects that do not require patterning, the researchers simply coat the area with HSQ and expose it to a plasma source.  The technique can make the nanoribbons up to 10 times more conductive than untreated graphene.

Because HSQ is already familiar to the microelectronics industry, the one-step approach to doping could help integrate graphene into existing processes, avoiding a disruption of the massive semiconductor design and fabrication system, Murali noted.

Over the past two years, researchers in the Nanotechnology Research Center had observed changes caused by application of HSQ during electrical testing.  Only recently did they take a closer look at what was happening to understand how to take advantage of the phenomenon.

For the future, they’d like to better understand how the process works and whether other polymers might provide better results.

“We need to have a better understanding of how to control this process because variability is one of the issues that must be controlled to make manufacturing feasible,” Murali explained.  “We are trying to identify other polymers that may provide better control or stronger doping levels.”

Research News
Georgia Institute of Technology
177 North Avenue
Atlanta, Georgia  30332-0181  USA

Media Relations Contacts: John Toon (; 404-894-6986) or Brett Israel (; 404-385-1933).

Writer: John Toon

Be Sociable, Share!